surges

General Talk

Moderators: OutBack, OutBack Moderator Team

Post Reply
mitch-moore@live.com
Forum Member
Posts: 6
Joined: Tue Sep 24, 2019 9:18 am
My RE system: outback vfxr3648a, Matte 3, 24 rolls 550s batteries
18 RenS la 255 watt panels, 18 370 watt panels, 10 port hub, 3 flexmax 80s
2, 11KW generac propane generators.
Location: Tulum MX
Contact:

surges

Post by mitch-moore@live.com » Sat Jul 11, 2020 5:19 pm

Hi, I have a 48 volt system, and I am having a lot of surges, even with low loads. I live in Mexico, and my tech says it's fine.

Sometimes the inverter crashes altogether, other times things like fans just slow down.

Any advice appreciated.

Thanks

Mike Curran
Forum Emperor
Posts: 1804
Joined: Sat Aug 28, 2004 6:28 pm
My RE system: Outback - Garage roof:
- 8 (2x4) Evergreen 180's into one FM80 (2007/2020 - replaced MX60)
- 6 (2×3) ALEO S79-300's into one FM80 (2017)
- 2 grid-tied GVFX3524's classic stacked for 120/240VAC (2007)
- 12 Surrette/Rolls 2V x 1766Ah (2007)
- Hub10.3, Mate3s, FNDC, RTS, OpticsRE. Tigo Energy ES maximizers on each PV module.

Westinghouse Solar - Barn roof: (2012)
- 30 (2x15) 235W panels with Enphase M215 microinverters, grid-tied

Outback Skybox - Barn roof: (2019)
- 14 Talesun 275W in series (DC array input to SB inverter/charger)
- 3 SimpliPhi 3.8 batteries, 48V, 225Ah total
- AC coupled input (manual switch during grid outage only) from 14 Talesun 275W,
Enphase M215 microinverters, normally direct grid tied

All self-designed and self-installed
Location: Chagrin Falls, Ohio

Re: surges

Post by Mike Curran » Sun Jul 12, 2020 7:43 am

Please elaborate on "surges". AC voltage? Current? More details are needed...
http://www.tigoenergy.com/site.php?95b2dca2-ca6c
https://enlighten.enphaseenergy.com/public/systems/Hctc107221

fcwlp
Forum Czar
Posts: 542
Joined: Wed Jan 22, 2020 9:40 am
My RE system: GS8048A, FM80 w/3,600 W PV Fixed, FM80 w/2,700W on Zomeworks tracker, Mate3, 24 Trojan 2V L16 1100AH @ C20, Grid-Tied with Kohler 14RESA LPG Generator and MEP-803 Diesel if needed
I also install and maintain grid-tied and off-grid systems, details will be given for these system if required
Location: 80 miles NE of Phoenix at 5500'

Re: surges

Post by fcwlp » Sun Jul 12, 2020 11:43 am

As this issue occurs when your loads are small, I expect that you are seeing a wide range of voltages coming from the grid. If you are on OpticsRE, go to your inverter and on the status page it will give you for today the low, current and high voltages coming from the grid. You can adjust the lower and upper AC in limits on the inverter's AC input page if on OpticsRE.

A couple of questions/thoughts:
1) Which of the seven modes is the inverter running?
2) Is this more of an issue in the summer? If in the summer is mostly during the day? It could be an issue with lots of AC units running in the area, stressing the grid. If major issue only during the day you could run in mini-grid mode during day using FLEXtime.
3) Are you selling back to the grid?

Post Reply